Motorcycle garage tools

On the other hand, working on a motorcycle with the right tools—like these—can be a pleasure. Snap-on Torque Wrench. When tightened to the proper torque—the right values can be found in a service manual—bolts will neither strip nor rattle loose. Like most torque wrenches, it clicks when you reach the specified torque. If, on the other hand, each cylinder doesn't get the same amount of fuel, a bike can be hard to start, can idle poorly, or can develop less power.

There are various tools available to help balance the fuel that reaches each cylinder, and these include mechanical and electronic vacuum gauges. The tools connect to tiny ports built in to each intake manifold—between the fueling system and the intake valves—and read the vacuum generated by each cylinder while the bike is running.

A screw between each carburetor or injector adjusts their relative openings for a given twist of the motorcycle's handgrip. Our favorite version is Morgan's Carbtune , which uses steel pucks that measure vacuum by sliding up clear tubes.

With it we balanced the carbs on our Ducati SS, and it's now running more smoothly than ever. RK Chain Tool. Sprocket replacement requires only undoing a few bolts, but installing the rivet-type master link found on most motorcycle chains is nearly impossible without a chain tool. We like the RK Chain Tool. With it, we installed and riveted the master link on a DID VX2 chain in seconds and with little effort.

The tool is too big to carry on the road, but it is perfect for the home mechanic. Mityvac Brake Bleeder. But before, you better make sure to have these tools available in your garage. We have listed the must have tools for motorcycle owners. Your motorcycle tires are probably the most obvious part of the vehicle, yet they are often overlooked as well.

However, maintaining tire condition is important as it is the part that makes contact with the road. Always check if your motorcycle tire is in the right pressure state before going out.

Under-inflated tires make poor handling and braking. Meanwhile, over-inflated tires reduce the area where the tires establish contact with the road, loosening its grip quality. With a pressure gauge, you can determine whether your tire needs more air or less and ensure a safer riding , as well as prolonging the life of your tires. Check the manual for the correct pressures. Your motorcycle is made from hundreds of spare part assembled into one with hundreds of bolts and nuts.

When you are performing a routine maintenance, sometimes you need to take them apart and sometimes you need to fasten them back. Torque wrench will do this job perfectly to fasten and unfasten rear axle nuts, front axle and pinch bolts, brake caliper bolts, engine and clutch cover bolts, cylinder head and head cover bolts, and so much more.

Check your manual to get the right values that will neither be too tight nor too loose. Choose a quality torque wrench that clicks when you reach the specified torque to ensure the accuracy. Screwdrivers are useful for a lot of thing, not only your motorcycle. It is an essential tool to screw and unscrews. Find a quality screwdriver with strong metal and hardened tips. The cheap ones usually use cheap metals that may not have a strong grip over the screws.

Look for the handle part as well. Handle with rubber gives your extra grip, especially when your hand is wet or dirty, therefore increase the leverage as well.

Also find one with a hex bolster at the base of the shaft, so in case you meet a particularly hard-to-turn screw, you can attach a crescent wrench on the bolster for additional leverage. Socket wrenches are essential tool for motorcycle or other vehicles maintenance. Like a more specific torque wrench and screwdriver, the main job of socket wrenches is to fasten and unfasten sockets.

The range is usually from 10mm to 17mm. Try to find if you can buy them individually with cheaper price. Motorcycle comes with side stand to park.

Bike stand comes off in either rear stand or front stand. Make sure to buy a quality bike stand with strong material, good balance and strength, also wide compatibility with various kind of motorcycle. It is not a difficult task and even a first owner of a motorcycle can learn to do it quickly. First, find out the location of the oil tank. Then, with the engine warm, remove the cap. All you need to do then is to wait, until the oil is drained.

Once the tank is empty, remove the filter. Replace the sump plug and the filter. Refill the engine with the new oil. This results in a load capacity of 1,pounds, more than enough for most bikes. Once loaded, the motorcycle is held in place with the built-in wheel-chock at the front of the loading platform. The main drawback to the Condor Motorcycle Garage Dolly is that can be slightly difficult to get the motorcycle loaded, especially if you have a heavier bike.

Overall, we would definitely recommend the Condor Motorcycle Garage Dolly as the best motorcycle dolly for most riders. This is a great dolly because it comes with a low profile design, making it easy to load or unload your motorcycle. With a weight capacity of 1, pounds, this dolly can be used with just about any bike. It even has an adjustable side tray, meant for the kickstand to help to keep your bike mounted on the platform.

For longevity, this dolly has been powder coated for rust and corrosion resistance. At each end of the dolly is a flip-up carriage. It can also be difficult to move if the floor is gritty and covered in debris. This is a simple, lightweight, and more affordable way of being able to maneuver your bike in tight spots.

The BikeMaster Adjustable Motorcycle Dolly is adjustable, making it a suitable choice for parking your bike in tight spaces. With a load capacity of 1, pounds, this dolly can be used with most motorcycles.

Keep in mind that it can accept rear tires up to 10 in wide, so double check your tire width beforehand. This makes it durable and reliable for mounting your motorcycle on to the loading platform.

One great feature worth mentioning is the kickstand arm. It can be easily adjusted to the point where your motorcycle kickstand naturally sits, resulting in your motorcycle standing in a more stable position. Once folded, it can be stored out of place and out of the way of everything else in the garage or parking space.

The main drawback to this dolly is that some people have mentioned it can be difficult to load a heavy bike with one person. This one is durable and ideal for smaller spaces, thanks to the adjustable design.

The Black Widow Steel Motorcycle Dolly is another option that takes advantage of the simple, streamlined design. With a weight capacity of 1, pounds, this model can be used with a wide range of different motorcycles.

Thanks to the strong, 12 gauge steel design, this is one of the most durable motorcycle dollies in our list. Other features worth mentioning include the integrated loading ramp, which allows for easily loading your motorcycle. It also comes with an adjustable kickstand plate and wheel safety pins, to prevent the dolly from rolling around with the motorcycle loaded. This is made even easier thanks to the ramp handles on either end of the loading platform.

This can be easily remediated by cleaning your workspace before loading the bike. A motorcycle dolly is one of the best motorcycle accessories or maintenance tools you could have in your motorcycle shed or garage.

This makes it easy to perform all of your motorcycle maintenance without the need of a motorcycle lift or other type of platform. These are ideal to have in smaller garages or tight parking spaces. To conclude, dollies help to clear up space and make it easier to maintain your bike. They also help with parking in smaller areas and moving your bike around more effectively.

Start by narrowing down what the most important features are you looking for. These features would include the weight capacity, durability, the weight of the dolly itself, and its overall maneuverability.